Welder Mma Arc

220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder

220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder
220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder

220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder

220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder. ACCORDING THE MACHINE TYPE USE POWER SUPPLY. 1 Check the connection of work piece, earth cable, welding torch, gas cylinder, regulator and hose, make sure they are firm and reliable. 2 Switch on the power source.

3 Turn on the gas valve, adjust gas volume to 3-5L/MIN. Check if there is gas leaking. 4 Hold the torch and keep tip of Tungsten electrode 2-3 mm above the work piece, and tilt 20-30 to vertical direction. Aim Tungsten electrode to the welding seam.

5 Push torch switch, after arc is ignited, move the torch along seam evenly. Fine tune the welding parameter to obtain exquisite welding seam.

Release the torch switch to finish a welding cycle. 6 After finish operation, turn off the gas valve, push torch switch to clear the residual gas in the regulator. At the end, turn off welding power source and wall switch. When using an open arc process, it is necessary to use correct eye, head, and body protection.

Fault code: E01 Overheating E02 Output control section is damaged or dead E03 Did not give the driver board signal, but the actual voltage output E04 Internal fault. Install procedure 1 Welding machine should be installed in a stable position and with good ventilation.

Avoid transport in invert or side position. 2 Connect electrode holder, earth cable, according to connection diagram. 3 Use 8 heat-resistant PVC hose connect the flow meter with the gas 4 Commission the machine after the machine is installed and tested.

The second function description Receiving arc voltage: MIG state when the function is Receiving arc voltage adjust MMA state when the function is arc force adjust Spot welding status, functions as spot welding time adjust Receiving arc current: MIG state when the function is Receiving arc current adjust MMA state when the function is welding current adjust Spot welding status, functions as spot welding interval adjust Electronic Inductor: MIG state when the function is electronic Inductor adjust MMA state when the function is invalid Spot welding status, functions as electronic Inductor adjust No displayheader Fan does not rotateNo welding output 1, confirmed air switch is closed. 2, the input cable connected to an electric power source.

Fans turnNo error codeNo welding output 1, the inspection machine all kinds of patch cords is bad. 2, the control circuit problem, find the cause, or contact your dealer.

3, on-off control lines torch. 5, ground off or not connected to the workpiece. 6, the internal cable off. Error code E01No welding output 1, may be overheating protection, wait 2-3 minutes to restore the machine to work.

2, the temperature switch is broken using the welding current does not remain stable during: 1, grid voltage changes; 2, severe interference from the power grid or other electrical equipment. 3, welding current and welding voltage is too low or too high, you should adjust the suitable welding current and welding voltage. 1We are a professional automotive tools company, with own factory located in China. 2We are a professional authorized dealers of.

Also offer reasonable prices , excellent customer service and a reliable credit standing are our target. 3 We own three warehouse in the world: China warehouse, United States warehouse, Germany warehous. Our normal working hours are from. All messages will be answered within 24 hours. You are welcome to write at any time! The item "220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder" is in sale since Friday, March 19, 2021. This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\TIG Welders". The seller is "obd-worldwide2019" and is located in Shenzhen. This item can be shipped worldwide.
  • Country/Region of Manufacture: China
  • Feed: Automatic Feed
  • Item Type: MIG Welder
  • Welding Process: MIG
  • Warranty: 3 Year
  • Features: Line Voltage Compensation
  • Welded Material: Stainless Steel
  • MPN: Does Not Apply
  • Brand: AUTOOL
  • Voltage: 110V OR 220V
  • Polarity: AC
  • Welder Industrial Class: Medium

220V TIG MIG IGBT Welding Machine Portable MMA ARC 160A with Gas Inverter Welder