Welder Mma Arc

TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A

TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A
TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A

TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A

TIG WELDER AC/DC FOR ALUMINUM AND STEEL. SHERMAN DIGITIG 200 AC/DC MULTIPRO is a inverter welding machine for professional applications. It is used for TIG welding of steel and non-ferrous metals (including aluminum and its alloys), but also allows arc welding due to dedicated mode and electrode holder included.

AMPERAGE RANGE - 5A - 200A. Welder SHERMAN DIGITIG 200 AC/DC MULTIPRO - Torch TIG SR26 - 4m. Stick electrode holder - 2m - Earth clamp - 2m. Gas hose with fittings - 2m. AC 210V - 240V / 50/60Hz / 1ph single phase.

48 x 20 x 33 cm. Welding aluminum requires a professional device that works with AC/DC current and has welding parameters like pulse welding and AC balance regulation. Sherman DIGITIG Multipro not only has those features but also allow to choose wave form for different aluminum alloys and material thickness. Welding current of 200A gives the possibility of obtaining 5mm penetration at 60% efficiency.

TIG Multipro uses digital control, which guarantees precise settings and parameter selection. The device has a memory of settings, so you can save the predefined parameters and return to them if necessary. Setting up the pulse will moderate the heat as you weld and ensure you have enough heat present at the joint.

The pulse setting gives you far more control over the welding process without compromising the strength and integrity of the welding joint. Variable waveform for different jobs. Sine waveform is the most popular. It allows you to get great results, the major advantage of the sine waveform is that it gives you a high peak current and an aggressive melt. Square waveform provides even deeper penetration when compared to both triangle waveform, and sine waveform.

Square waveform is especially helpful when pushing, spreading, and smoothing metal. Trapezoid waveform provides a smooth, soft, "buttery" arc with a fluid puddle and good wetting action. The puddle is more fluid than with advanced square wave and more controllable than with sine wave.

Triangle waveform offers peak amperage while reducing overall heat input into the weld. This leads to quick puddle formation, low weld distortion, and fast travel speeds. It is especially good for welding thin aluminum.

Device allows you to store predefined values in the memory. It is useful when the same job is frequently repeated and there's a need to use identical parameters. It saves a lot of effort reducing time taken to get your device going. Memory can store up to 20 sets of settings. Additionally device can restore last used values after the it was turned off and on again.

In 2T mode, operation is fairly simple. Activating the torch in 2T mode is a process of pressing the trigger and holding it down during welding process. This mode is dedicated for beginners and tasks where it is more suitable. To operate, simply press and hold the torch trigger.

When a puddle begins to develop you can release the trigger and the device automatically begins the preset cycle until it reaches full operating amperage. To terminate the weld, simply press and hold the switch again until device end the welding cycle.

High frequency arc ignition (HF). The High Frequency start is a touch-less method and creates almost no contamination. Once your arc is started, the high frequency function is turned off until you are ready to start the arc again. In particular, it relates to the circuit board and the inverter. It does not extend to the housing and its external components and connecting parts, such as the hose pack or the mass clamp. We deliver all over Europe.

You can be sure your parcel arrive on time. Our professional customer service team is here for you seven days a week. You will be provided with the best customer service so you won't walk away unsatisfied. The item "TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A" is in sale since Thursday, February 28, 2019.

This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\TIG Welders". The seller is "allweld_supplies" and is located in Rzeszów. This item can be shipped worldwide.
  • Model: SHERMAN TIG MULTIPRO AC/DC
  • Modified Item: No
  • Country/Region of Manufacture: Poland
  • Custom Bundle: No
  • Item Type: Inverter Welder
  • Welding Process: TIG
  • Polarity: AC/DC
  • Adjustment: Stepless
  • Pre/Post gas: Adjustable
  • Pulse welding: Fully adjustable
  • Transistor technology: IGBT
  • Supply voltage: AC 210V - 240V / 50/60Hz / 1ph single phase
  • Torch type: SR26 4m
  • Welder Industrial Class: Light
  • Welded Material: Aluminium
  • MPN: 7811876
  • Amperage range: 5A - 200A
  • No load voltage: 67V
  • Featured Refinements: Arc Welder
  • Duty cycle: 60%
  • Arc ignition: HF
  • Unit Type: Unit
  • Settings memory: YES
  • Wave form selection: YES
  • Brand: SHERMAN

TIG MMA Arc welder Welding machine AC DC Aluminium Pulse SHERMAN MULTIPRO 200 A